Sigfox Ready™ Certification for End ProductChecklist

End Product Certification Checklist
Sigfox ref # SIGFOX INTERNAL REFERENCE
1 / 4: General information
Address where the device is to be returned by the lab after End Product certification / Enter the name and the address of the company where the end product is to be returned after certification
Technical contact / Name:enter the name of the technical contact that will follow the certification
Email:
Phone:
Manufacturer name and ref. of embedded transceiver, SOC or module / Enter the name of the modem manufacturer
Enter the name of the module or ref design
Sigfox Verifiedfirmware revision / Enter the revision of the embedded firmware
Sigfox Verified certificate ID (Eg: M_001_9C0B_01) / Enter the certificate Identifier of the Sigfox Verified modem (can be provided by the modem manufacturer or in the Sigfox Verified certification report)
ID of the Product to be tested (Sigfox Identifier)
Eg: 0x00001A34 / Enter the unique Sigfox identifier available when registering the device into the Sigfox cloud
Targeted usage / □ POC (Proof of concept)
□ Commercial
Product communication mode / □ Uplink only
□ Uplink & Downlink
2 / 4 : Technical information
Power Supply of product to be tested (to be provided in the same mode as when operational onSigfox network) / □ Battery powered / □ External power supply (to be provided) / □ Other:
Radio Configuration: / RC1 / RC2 / RC3 / RC4
CFU: Central Frequency Uplink (Operating frequency on Sigfox network) / □ 868.13MHz / □ 902.2MHz / □ 923.2MHz / □ 920.8MHz
CFD: Central Frequency Downlink if applicable (Operating frequency on Sigfox network) / □ 869.525MHz / □ 905.2MHz / □ 922.2MHz
To be confirmed not yet available / □ 922.3MHz
End Product timestamps to check hopping on Sigfox network (at least 10 consecutive messages) / Start Transmitting time & date:
Date: ………. / ………. / ………
Time: ……. H ………. M ……. S / Stop Transmitting time & date:
Date: ………. / ………. / ………
Time: ……. H ………. M ……. S
Copy date and time of the start and stop of 10 consecutive messages of the DUT reported by the device in the Sigfox cloud
Reference device (Keyapp or Sigfox demonstrator) timestamps to compare RSSI levels (at least 10 consecutive messages at same date / location / position / environment as End product) / SigfoxReference device ID (if any):
Start Transmitting time & date:
Date: ………. / ………. / ………
Time: ……. H ………. M ……. S / Stop Transmitting time & date:
Date: ………. / ………. / ………
Time: ……. H ………. M ……. S
Copy date and time of the start and stop of 10 consecutive messages of a reference device (keyapp, SNT, FTD…) reported by the device in the Sigfox cloud if you have one.
Declared Downlink End Product sensitivity (in dBm). Mandatory for Downlink products / Enter declared or measured sensitivity of the product
CW test mode Transmission Frequency (for End Product certification) / To be set to product CFU value
Describe CW test mode Power On /Power OFF sequence (Continuous Wave mandatory) or quick start guide if complex power ON / power OFF
Please respect CFU central frequency uplink / Power ON
describe precisely how to power ON the CW (continuous wave) test mode (hardware :button, switch, ILS….; software : AT commands …) Add picture or user guide if needed
Power OFF
describe precisely how to power OFF the CW (continuous wave) test mode (button, switch, ILS….) Add picture if needed
2 / 3 : Technical information (cont.)
End Product Photo(s) / Insert a picture or photograph of the end product to be tested
Photo of end productin normal use position in the applicative environment as declared by the provider / Insert a picture or photograph of the end product to be tested, in normal use position and in its environment
Photo or schematic of end productposition for effective radiated power measurementin laboratoryif different from normal use position /
Insert a photo with the position of the device when performing the radiation measurements. Be aware that this position will determine the Sigfox class of the product
Antenna type / □ ½ Wave antenna
□ Wire antenna
□ PCB antenna
□ ¼ Wave antenna
□ Ceramic antenna
□ Fractal antenna
□ other:
Choose antenna type (multiple answer possible)
4 / 4 : Technical information (cont.)
Antenna reference or link to datasheet
If no datasheet provided: Antenna characteristics (polarization, gain (dBd or dBi), bandwidth,impedance, efficiency, Ros or VSWR, radiation pattern, connector type…)
Internal photo of end product with antenna to modem path / Provide an internal picture of the product showing the antenna and path to the output of the modem to the antenna

Upon checklist approval, End Product shall be shipped to the certification lab mandated by Sigfox(address will be provided) to perform End Product measurement testing.

Version: 1319/04/2017