PROJECT NAME
DATE
____________________________________________________________________________
SECTION 10 22 44
SLIDING-STACKING PARTITIONS
PART 1 – GENERAL
**NOTE: THE PK30 SLIDING/STACKING SYSTEM IS A HARDWARE SYSTEM FOR STACKABLE PARTITIONS WEIGHING FROM 154 TO 330 LBS (70 TO 150 KG) PER PANEL. THE MODULAR TRACK SYSTEM AND ITS UNRIVALLED CORNERING TECHNIQUE PERMITS ALL DESIGN CONCEPTS OF ROOM PARTITIONS TO BE REALIZED QUICKLY AND WITHOUT PROBLEMS. THIS HARDWARE SYSTEM ALLOWS STRAIGHT TOP TRACKS / BOTTOM GUIDE CHANNELS AND CURVED SEGMENTS OF 15, 30, 45, 60, 75 AND 90 DEGREES TO BE COMBINED TO FORM INDIVIDUAL CONFIGURATIONS. DIFFERENT TROLLEYS ARE REQUIRED DEPENDING ON THE DOOR WEIGHT. THE SLIDING-STACKING PARTITIONS CAN BE MOVED INTO PARKING AREAS, EITHER PARALLEL OR AT PERPENDICULAR TO THE SLIDE AXIS. THE USE OF CONTINUOUS BOTTOM GUIDE CHANNELS IS NOT MANDATORY. THE BROAD APPLICATION RANGE REQUIRES THAT THE PK30 SLIDING/STACKING SYSTEM BE CUSTOM ENGINEERED TO ATTAIN THE BEST SOLUTION FOR A GIVEN PROJECT.**
**NOTE: SPECIAL CONDITIONS CAN BE ACCOMMODATED. PLEASE CONTACT PK30 SYSTEM IF YOUR PROJECT HAS UNUSUAL REQUIREMENTS OR CONDITIONS THAT HAVE NOT BEEN SPECIFICALLY ADDRESSED. SPECIALIZED SOLUTIONS ARE AVAILABLE UPON REQUEST.**
1.1 SUMMARY
A. Section includes sliding-stacking partitions as shown on the drawings, inferable therefrom and as specified.
1. Sliding-stacking partitions includes the following: Provide all elements from a single manufacturer.
**NOTE: EDIT “a” BELOW FOR THE TYPES OF PARTITION SYSTEM FOR THE PROJECT.**
a. Metal framed glass sliding-stacking partitions including all accessories.
**NOTE: THE SYSTEM MAY INCLUDE SWINGING DOORS. DELETE BELOW IF NO DOORS AND REVIEW THE ENTIRE SECTION CAREFULLY WHERE OTHER REFERENCES TO DOORS SHOULD BE DELETED.**
b. Integrated metal framed glass doors including all accessories.
1.2 REFERENCES
B. Reference Standards: Publications referenced in the text of this Section are listed by source, designation, where applicable, and title.
1. AAMA 611.98: Voluntary Specification for Anodized Architectural Aluminum.
1.3 ADMINISTRATIVE REQUIREMENTS
A. Coordination:
1. Single Responsibility: Assign undivided responsibility of the sliding-stacking partitions to a single firm specializing in this type of work. Do not engage a firm unacceptable to the manufacturer of the system. The firm shall engage other specialty firms to perform any part of the work which he is not equipped or qualified to perform with their own personnel.
**NOTE: CHOOSE ABOVE OR BELOW. ABOVE FOR USE OF JUST THIS SECTION. BELOW WHERE SOME OR ALL OF THE FOLLOWING SECTIONS ARE PART OF THE PROJECT.**
1. Single Responsibility: Assign undivided responsibility of the following scopes of work to a single firm specializing in these types of work. Do not engage a firm unacceptable to the manufacturer of the system. The firm shall engage other specialty firms to perform any part of the work which he is not equipped or qualified to perform with their own personnel.
**NOTE: EDIT BELOW FOR ONLY THOSE SECTIONS USED.**
a. Section 10 22 19, DEMOUNTABLE PARTITIONS.
b. Section 10 22 39, FOLDING PARTITIONS.
c. Section 10 22 43, SLIDING PARTITIONS.
d. Section 10 22 45, OFFICE ENTRANCES.
**NOTE: USE “2” ONLY WHEN CHOOSING THE SECOND OPTION FOR “1” AND EDITE THE REFERENCE SECTIONS AS REQUIRED.**
2. Coordinated Submittals: Coordinate submittals with the following Sections:
a. Section 10 22 19, DEMOUNTABLE PARTITIONS.
b. Section 10 22 39, FOLDING PARTITIONS.
c. Section 10 22 43, SLIDING PARTITIONS.
d. Section 10 22 45, OFFICE ENTRANCES.
B. Preinstallation Meetings: Prior to the installation of sliding-stacking partitions, and at the Contractor's direction, meet at the project site to review the installation procedures and methods.
1.4 ACTION SUBMITTALS
A. Product Data: Submit manufacturer's product data and hardware details including rough in requirements and dimensions, installation instructions, and parts lists for all sliding-stacking partitions and accessories required.
1. The broad application range requires that the HAWA-Variotec 150/H Modular wall hardware system be custom engineered to attain the best solution for a given project.
**NOTE: BELOW IN SHOP DRAWINGS, THE SUPPORT FOR THE SYSTEM IS NOT INCLUDED. SYSTEM REQUIREMENTS FOR THE SUSPENSION TRACK ARE DEPENDENT UPON THE STRUCTURE/ARCHITECTURE OF THE GIVEN APPLICATION, THEREFORE THE ARCHITECT/DESIGNER’S ENGINEERING CONSULTANT SHOULD DETERMINE THE NECESSARY STRUCTURAL REQUIREMENTS FOR SUPPORTING THE SUSPENSION TRACK ACCORDING TO LOCAL CODES AND CALCULATIONS MADE OF EXISTING CONDITIONS. PK30 WILL OFFER ALL ASSISTANCE POSSIBLE INCLUDING BUT NOT LIMITED TO PANEL WEIGHTS, COMBINED PARKING AREA WEIGHTS FOR LOADING CALCULATIONS, AND EXAMPLES OF POSSIBLE SUPPORT METHODOLOGIES.**
B. Shop Drawings: Prior to ordering materials, submit shop drawings for the fabrication and installation of sliding-stacking partitions. As specified under Existing Conditions, note all field measurements required on the shop drawings. Include large scale elevations, details, and sections of all component members anchorage, jointing, and other accessories as follows:
1. Layout and installation details, including relationship to adjacent work.
2. Elevations at minimum 1/4 inch equals 1 foot scale.
3. Detail sections of typical members.
4. Anchors and reinforcement.
5. Hardware mounting locations including dimensions.
6. Glazing details.
C. Samples:
1. Initial Selection Requirements:
a. Colors: Provide manufacturer’s standard coupon samples of each color required.
2. Verification Requirements: Provide only after approval of color selections.
a. Profiles: Submit the required sets of samples of each component with each finish on 12 inch long sections. Where color variations are anticipated include two or more units in each set of samples indicating the anticipated range.
b. Corner Fabrication: 8 inch long legs of full-size corners, including full-size sections of extrusions with factory-applied color finish.
c. Glazing: Manufacturer's standard-size unit, but not less than 3 inches square.
1.5 INFORMATIONAL SUBMITTALS
A. Sustainable Design Submittals:
1. Recycled Content: Submit certification letter from material suppliers certifying specified percentage requirements of recycled content indicating percentages by weight of post-consumer and pre-consumer recycled content. Include statement indicating costs for each product provided.
1.6 CLOSEOUT SUBMITTALS
A. Operation and Maintenance Data:
1. Provide manufacturer's care instructions for maintenance of sliding-stacking partitions including cleaning instructions, operating instructions and precautions, and any limitations.
B. Warranty Documentation: Provide signed warranty as specified.
1.7 QUALITY ASSURANCE
A. Qualifications: Personnel engaged in the work shall be able to demonstrate successful experience with work of comparable extent, complexity and quality to that shown and specified, including quality control and testing procedures. This includes the following additional requirements:
1. Manufacturers: Capable of providing complete, precision built, engineered, pre-fitted units with a minimum 10 years’ experience in the sale of folding-sliding door systems for large openings in the North American market.
2. Installers: Experienced in the installation of the manufacturer’s products or other similar products for large openings. Provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years.
a. Installers shall be trained and certified by the manufacturer.
**NOTE: BELOW FIRST TIME INSTALLER PROGRAM’S INSTALLATION SUPERVISION AND ASSISTANCE COSTS $700.00 PER DAY PLUS TRAVEL AND HOTEL EXPENSES. A 2 DAY CERTIFICATION SERVICE IS THE MINIMUM REQUIREMENT FOR INSTALLATION CERTIFICATION. INSTALLATIONS WITHOUT PK30 CERTIFICATION ARE NOT WARRANTED. SERVICE CALLS TO ADJUST AND REPAIR THE PK30 PRODUCT ON UNCERTIFIED INSTALLATIONS WILL BE BILLED TO CUSTOMER AT A RATE OF $700.00 PER DAY PLUS TRAVEL AND LODGING EXPENSES.**
b. First Time Installer Program: Where the installer has been trained and certified by the manufacturer but where this is the installer’s first time installation of the manufacturer’s product, the manufacturer shall provide a full time, on site, installation supervisor for a minimum of 2 days to ensure that the system is correctly installed
B. Single Source Limitation: Provide all components and accessories for sliding-stacking partitions from a single manufacturer.
1.8 DELIVERY, STORAGE, AND HANDLING
A. Delivery, Storage and Handling Requirements: Deliver materials to job site in manufacturers original sealed, unopened cartons or crates. Protect units from damage. Store on pallets in dry, weather protected locations and free from dirt, dust, construction debris. Comply with the manufacturer’s requirements for protection including limitations for the contact of any protective materials. Storage area shall be free from the requirement to move or relocate delivered materials prior to installation.
1.9 SITE CONDITIONS
A. Ambient Requirements: Do not deliver or install sliding-stacking partitions or components until the installation site is enclosed and all finishing including ceiling, floor covering and painting are completed.
B. Existing Conditions:
1. Manufacturer’s shop drawing dimensions, including tolerances shall be based on the Architect’s drawings.
2. Verify with field measurements prior to fabrication the dimensions of openings, and stack storage area. Mark field measurements on shop drawing submittal.
3. Where field dimensions cannot be verified, the General Contractor shall be responsible for maintaining the tolerances required for installation.
1.10 WARRANTY
A. Manufacturer’s Warranty: Submit copies of written warranty, signed by the manufacturer and the installer, agreeing to repair or replace defective components and work which has failed. Repairs and replacements required because of failure of materials or workmanship shall be completed without additional expense to the Owner. The period of the warranty shall be an extension to 2 years starting on the date of acceptance by the Owner for substantial completion. Failures include but are not limited to the following:
1. Component structural failure including excessive deflection.
2. Faulty operation of components or hardware.
3. Deterioration of metals, metal finishes including coatings.
PART 2 – PRODUCTS
2.1 SYSTEMS
A. Manufacturer: Substitutions will not be permitted. Provide precision built, pre-engineered, pre-fitted sliding partition system from the following:
1. PK30 System LLC
PO BOX 656
3607 Atwood Road
Stone Ridge, NY 12484
(212) 473-8050 (845) 687-9774
website: www.pk30.com
email:
**NOTE: EDIT BELOW IF NO SWINGING DOORS.**
B. Product: Sliding partition system for sliding-stacking metal framed panels and integrated metal framed glass door including all hardware, accessories, and anchorages.
1. PK30 System.
C. Sustainability Requirements:
**NOTE: BELOW IS BASED ON LEED V3. VERIFY AND MODIFY AS REQUIRED.**
1. Recycled Content:
a. Products shall have a minimum recycled content of 40 percent pre-consumer and 22 percent post consumer.
D. Performance/Design Criteria: Provide partitions and doors of dimensions and configurations shown complying with performance requirements specified.
1. Loading:
a. Withstand gravity loads.
b. Limit lateral deflection to less than L/175 or 3/4 inch, whichever is less, complying with ASTM E72 tested under a uniformly distributed load of 5 pounds per square foot.
2. Glass Deflection:
a. Limit lateral deflections of glass panel edges to less than L/175 of glass-edge length or 3/4 inch, whichever is less.
E. Materials:
1. Aluminum: Alloy and temper recommended by the manufacturer for strength, corrosion resistance, and application of required finish.
a. Comply with the following:
1) Aluminum Extrusions: ASTM B 221, Alloy 6063, T6,T5/T52.
2) Aluminum Sheet or Plate: ASTM B 209, Alloy 6061, T6.
3) Aluminum Bars, Rod and Wire: ASTM B 221, Alloy 6063, T6.
b. Provide main extrusions of not less than 0.080-inch wall thickness, profiles as shown.
c. Provide extruded glazing stops and other applied trim extrusions with minimum wall thickness of 0.050-inch.
2. Fasteners; Provide 18/8 stainless steel, or other non-corrosive metal fasteners compatible with aluminum components, hardware, anchors, and other items being fastened.
a. Reinforcement: Where fasteners screw anchor into aluminum extrusions where there is no screw boss, or that is less than 0.125-inch thick, reinforce the interior with aluminum or steel as required to receive screw threads.
b. Exposed fasteners: Provide all exposed fasteners shall be flat socket head or Phillips head 18/8 stainless steel machine screws, use only one type of exposed fastener for all work.
3. Glazing:
a. Glazing System: Use manufacturer's standard glazing system of setting blocks, gaskets, and glazing tapes as required to cushion the glass and prevent metal to glass contact.
b. Glass: Provide manufacturer’s glass of the type as selected by the Architect. Where custom glass is selected, coordinate with the sliding partition manufacturer for factory glazing before shipment to the site.
**NOTE: DELETE BELOW OR SPECIFY AS REQUIRED. THE SYSTEM CAN ACCOMMODATE MANY PANEL TYPES (WOOD, GLASS, PLASTIC, METAL) WITH A THICKNESS RANGING BETWEEN 1/4 INCH AND 9/16 INCH. WHERE WOOD IS COORDINATE WITH ARCHITECTURAL WOODWORK, CONSIDER REFERENCING SECTION 06 40 00 AND DESCRIBE THE WOOD PANELS THERE COORDINATING THAT THEY ARE REQUIRED TO BE PROVIDED TO THE PARTITION INSTALLER FOR INSTALLATION.**
c. Panels: xxx.
F. Fabrication:
1. Provide shop assembled panels with hardware and accessories required for a complete assembly. Provide concealed fastening devices and pressure-fit components that will not damage ceiling or floor coverings. Fabricate panels with light and sound seals at floor, ceiling, and other locations where panels abut fixed construction.
2. Factory prepare interior aluminum frames to receive templated mortised hardware; include cutouts, reinforcements, mortising, drilling, and tapping,
3. Fabricate frames for glazing with removable stops to allow glazing replacement without dismantling frame.
4. Fabricate components to allow secure installation without exposed fasteners.
G. Design Configuration:
**NOTE: COORDINATE ALL OF THE CONFIGURATIONS DESCRIBED WITH WHAT IS SHOWN DELETE THOSE NOT REQUIRED.**
1. Sizes and Configurations: As shown for selected number and size of panels, location of swing panels, and location of tracks and stacking bays.
2. Operation: Adjustable sliding and swinging hardware with the following track options:
**NOTE: EDIT BELOW TRACK CONFIGURATIONS AS REQUIRED.**
a. Top and bottom tracks.
b. Top tracks, bottom track will not be permitted.
c. Top and bottom tracks as shown, some locations a bottom track will not be permitted.
3. Panel Configurations:
**NOTE: EDIT BELOW PANEL CONFIGURATIONS AS REQUIRED.**
a. Straight.
b. Segmented curve.
c. 90 degree corner.
4. Storage Stacking Configurations:
**NOTE: EDIT BELOW STORAGE STACKING CONFIGURATIONS AS REQUIRED.**
a. Remote pocket.
b. Behind swing door.
c. Parallel parking.
d. Perpendicular parking.
e. Specialized parking.
5. Mounting Types:
**NOTE: EDIT BELOW MOUNTING TYPES AS REQUIRED.**
a. Top hung.
b. Surface mounted.
c. Recessed mounted.
H. Finishes:
**NOTE: DELETE OR EDIT THE DIFFERENT FINISH SYSTEMS AS REQUIRED. A PROJECT MAY HAVE ONLY ONE OR SEVERAL DIFFERENT SYSTEMS, OR SEVERAL COLORS OF BAKED ENAMEL. COORDINATE WITH DRAWINGS AS REQUIRED TO DESIGNATE LOCATIONS.**
1. Anodized Coating: Provide the following for all aluminum work shown or specified to receive anodized finishes, NAAMM nomenclature, as required to match Architect's sample:
a. Clear Anodized Finish: AA-M12C22A41, Class I, 0.07 mm or thicker.
1) Color: Manufacturer’s medium matte clear finish.
b. Color Anodized Finish: AA-M12C22A42/A44, Class I, 0.07 mm or thicker.
1) Color: Manufacturer’s medium matte black finish.
2. Baked Enamel Coating: Thermosetting acrylic enamel coating shall be factory applied and shall meet the high performance requirements of AAMA 2603.