KARBI ANGLONG AUTONOMOUS COUNCIL
OFFICE OF THE
EXECUTIVE ENGINEER, HOWRAGHAT DIVISION
PUBLIC HEALTH ENGINEERING DEPARTMENT
DETAILED TENDER DOCUMENT
FOR
GREATER DOKMOKA-TEKELANGJAN WATER SUPPLY PROJECT
(SH : Construction of Laboratory room, Chemical house, Office – cum – operator’s room as per approved drawing of the department for Greater Dokmoka - Tekelangjan Piped water supply Project under NLCPR)
(PART – B: THE SCHEDULE OF WORKS & PRICE BID)
THE SCHEDULE OF WORKS & PRICE BID
Name of work : Construction of Laboratory room, Chemical house, Office – cum – operator’s room as per approved drawing of the department for Greater Dokmoka - Tekelangjan Piped water supply Project under NLCPR
SL. NO. / Specification / Unit / Quantity / Rate in figure and word1 / Earth work in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity necessary after completion of work, breaking clods in return filling, dressing, water
A) Up to a depth of 2.00 m below the existing ground level.
e) In hard rock
(ii) Without using blasting materials (where blasting is not possible/not permissible) / Cum / 113.72
2 / Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be meas / Cum / 12.36
3 / Earth / sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete ……. And other duties and taxes as may be necessary.
c) With river sand or silt (predominately nonplastic) by truck carriage in / Sqm / 54.27
4 / Providing and laying 25mm thick damp proof course with cement concrete in prop. 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing et / Sqm / 9.88
5 / Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete
(A) In sub-structure upto plinth level
Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level.
(a) M15 / Cum / 26.521
(B) Super-structure from plinth level upto 1st floor level.
(ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumers, cantilever, staircase (except spiral stair case and landing) including preparing the top surface and finishing o / Cum / 27.842
6 / Providing form work of timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ rein
Foundation, footings, base of columns, pile cap, raft and mass concrete works etc.
(ii) Using 25mm thick plank / Sq.m / 17.50
Sides of tie beams, grade beams etc. at or below ground level
(ii) Using 25mm thick plank / Sq.m / 95.09
Columns, Pillars, Posts & Strut
(ii) Using 25mm thick plank / Sq.m / 59.94
Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.
(a) For depth not exceeding 1.0M
(ii) Using 25mm thick plank / Sq.m / 128.57
Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconies and the like.
(a) Floors etc. upto 200mm in thickness
(ii) Using 25mm thick plank / Sq.m / 156.98
7 / Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.
(a) Brick on flat soling / Sq.m / 146.81
8 / Brick work in cement morter with 1st class brick including racking out joints and dewateing if necessary, curing complete as directed in sub-structure upto plinth level.
(b) In proportion 1:4 / Cum / 11.81
9 / 112mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto 1st floor level (protruding M.S rod / Tor steel of column to be embeded in cement mortar and will be / sq.m / 162.94
40mm thick cement concrete floor ……… …… ….. …….. Of floor area including curing etc. complete as directed. / sq.m / 90.45
Cement plaster skirting with cement …………… …. ………. Rounding of junctions with floor
(a) 15mm thick / sq.m / 51.84
10 / Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10mm thick in prop. 1:3 (1 cement : 3 coarse sand) …… …...... (Walls means both
a) Normal ramge (sizes 300mm x 200mm and above)
d) Asian made / Sq.m / 22.50
11 / 15mm thick Cement plaster in single coat on fair side of brick / concrete walls for interior plastering up to 1st floor level including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smo / sq.m / 318.55
12 / 20mm thick Cement plaster in two coats, backing coat 15mm and finishing coat 5mm thick on rough side of single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles, chamfers and / or rounded angles no / sq.m / 175.61
13 / Extra over item no. 6.2.1 to 6.2.5 for plastering on ceiling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed. / Sq.m / 138.55
14 / Providing wood work in frame (chowkaths) of doors, windows, clerestorey windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mm x 3mm / Cum / 1.14
15 / Providing, fitting and fixing fully glazed window with sash bars including oxidised M.S. butt hinges (75mm x 60mm x 3.15mm) 2 nos. on each leaf and 3 nos. on single leaf (glass panes to be measured and paid separately)
A) With Teak wood / Sissu wood
(i) 4 / Sq.m / 14.31
16 / Providing, fitting and fixing fully glazed clerestory window and fan light including fitiing and fixing 2 M.S. pivot hinges (75mm x 20mm x 3mm), eye hook and nylon chord complete (glass panes shall be measured and paid seperately).
A) With Teak wood / Sis / Sq.m / 5.40
17 / Providing fitting and fixing full panelled doors …….. …………. Fittings to be measured and paid seperately)..
B) With 1st class local wood (Hollock / Bonsum).
Ii) 30mm thick / Sq.m / 21.74
18 / Providing, fitting and fixing M.S. grill of required pattern for windows / clerestory windows / opening with M.S. flats at required spacing in frame all round, square or round M.S. bars with round headed bolts and nuts or screws.
II. Ornamental grill
(a) / kg / 108.00
19 / c) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on old wall surface (one coat) to give an even shade after thoroughly brooming the surfaces to remove all dirt and remains of loose or softened pain / Sq.m / 99.81
d) Extra over item no. (b) and (c) above for every subsequent coat of water proofing cement paint of approved brand and manufacture. / Sq.m / 99.81
20 / Distempering with dry distemper of approved ……… ………………………….. Foreign matter and including preparing the surface sandpapered smooth. / Sq.m / 393.39
21 / Applying priming coat over new wood based surfaces upto 100mm in girth / width after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting.
(b) With ready mixed paint, wood primer / R.m / 93.76
22 / Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint / J&N paint / Nerolac) to give an even shade including cleaning the surfaces of all di
(i) Surfaces over 100mm in width or girth.
b) High gloss (Asian paint / Berger paint / ICI paint / J&N paint / Nerolac). / Sq.m / 93.76
23 / Applying primary coat over new steel and other metal surface over 100mm in width or girth after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand pape / Sq.m / 19.71
24 / Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint / Berger paint/ ICI paint / J&N paint/ Nerolac) to give an even shade including cleaning the surface of all d
(i) Surfaces over 100mm in width or girth.
b) High gloss (Asian paint/ Berger paint / ICI paint / J&N paint / Nerolac). / Sq.m / 19.71
25 / Supplying, fitting, fixing anodisied aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects ………….. …….. ………….. (anodised to bright natural matt & satin finished).
a) Sliding door bolts
i) 250mm x 16mm / Each / 3
b) Tower bolts
iv) 150mm x 10mm / Each / 25
e) Door handles
iii) 150mm / Each / 45
d) Gate shutter hook & eye
ii) 150mm / Each / 40
e) Butt hinge
i) 125mm x 50mm x 4mm / Each / 36
ii) 100mm x 50mm x 4mm / Each / 36
26 / Providing and fixing clear sheet glass beded in putty and fixed with / without wooden bidding including necessary cutting and glass to be required sized (payment for wooden bead shall be made seperately)
(1) Area of glass panes not exceeding 0.15 m2
(c) 3.00mm thick / Sq.m / 5.38
27 / Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G a
b) ISI approved super ductile TMT Bar
(i) TATA/SAIL / Qtl / 37.48
28 / Providing fitting and fixing vitreous water closet squatting pan (Indian type pattern) of size 580 x 440mm with 100mm SCI 'P' or 'S' trap, ………………….. …………….. …………….. ……... the walls and floors wherever required.
(a) White / Each / 2
29 / Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/ Prince) or other ISI approved including jointing, fitting and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified.
a) In exposed surfaces or in trenches.
(ii) 110mm dia / R.m / 20.00
(iii) 90mm dia / R.m / 15.00
b) Concealed by chiselling or breaking brick wall / C.C./ R.C.C. and making good to the damages.
(ii) 110mm dia / R.m / 5.00
(iii) 90mm dia / R.m / 6.00
30 / Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme / Prince) or other ISI approved including jointing, fitiing and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. / Each / 3
a) In exposed surfaces or in trenches.
(ii) 110mm dia
31 / Supplying, fitting and fixing 87.5 degree PVC bend with door of (Supreme / Prince) or other ISI approved including jointing, fitiing and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.
a) In exposed surfaces or in trenches.
(ii) 110mm dia / Each / 3
32 / Supplyin fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc. complete at all levels including below G.L. as
b) 40mm dia
i) Using Tata (medium) / R.m / 15.00
f) 15mm dia
i) Using Tata (medium) / R.m / 20.00
33 / Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified (G.I. & C.P. pipes will be measured seperately).
(I) Essco make (Delux / Sumthing spl. / Tropical)
(b) Long body bib cock with wall flange / Each / 5
34 / Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified. (G.I. & C.P. pipes will be measured and paid separately).
(II) Agmeco Brand
(a) 15mm dia (Male / Female) / Each / 5
35 / Wiring for light point with 1.5 sq. mm P.V.C.insulated unsheathed 1.1 K.V. (R.R Kabel/finolax/Havells make) single cover conductor cable in surface PVC casing caping conduit wiring system including 6 Amps...... as required complete in 19 mm dia rigid
a) Short point up to 3.0 M. length / point / 309.63
b)Medium point up to 6.0 M length. / point / 481.15
c) long point up to 10 m length / point / 695.48
36 / Wiring as of Item No. above in surface PVC conduit wiring system with 19mm dia, rigid PVC casing caping conduit to a fan /
exhaust fan point.
a) Short point up to 3.0 M. length / point / 352.41
b)Medium point up to 6.0 M length. / point / 531.08
c) long point up to 10 m length / Per point / 735.47
37 / Supplying including fitting fixing of high speed AC ceiling fan complete with all sccessories like down rod, canopy etc.……. with maling necessary connections etc as required complete and as directed by the department
c) 1050 mm sweep / Each / 1690.47
38 / Wiring to a 5 pin, 6 Amp. Plug point with 1.5 sq.mm PVC insulated unsheathed coper conductor cable in recessed 19 mm dia PVC conduit ………….laminated sheet cover ceiling rose etc