Installation instruction for illuminated LED door sills.
Note!!!
- Before the installation, please make sure door sills do not rub on the bottom of the door when it is closed.
- It is recommended to install and connect illuminated door sill light to the vehicle electrical system by professional automotive electrical technicians.
1. Clean the surface of the installation thoroughly and remove any dirt using enclosed 3M tissue.
2. Put the door sill on the ledge and mark the right position by marker or paper tape.
3. Remove the adhesive tape protection then put the door sill on the marked position, you can tape it begin with an upper edge and precisely press on the whole surface.
4. Press on the top of the tape to make sure the door sill fix firmly.
5. Connect the wires to the vehicle electrical system correctly. Please access the positive and negative poles of the power through voltage regulator rectifier. Do not access to car battery directly!
6. Take off the protective film on the door sill surface.
Note:
- Self-adhesive tape is very strong!
- Optimal for installation is 10 °C - 30 °C
- The installation surface should be clean, dry and precisely degreased to guarantees durability of the adhesive.
- Pay attention to waterproof and moisture.
- It’s better not to keep the door sill working more than 60 minutes continuously to avoid the damage of LED chips!!!
- The manufacturer is not liable for any damage caused by improper installation.
Technical data:
1. Supply voltage: DC 12V, red wire(+), black wire (-) .
2. Working current ≤ 600 mA.
3. Working Temperature: -20°C ~50 °C
Instrukcja instalacji podświetlanych nakładek progowych LED
Uwaga !!!
- Przed instalacją upewnij się, że nakładki progowe nie ocierają wewnętrznej części drzwi gdy są zamknięte.
- Zaleca się instalować i podłączać podświetlane nakładki progowe do elektrycznego systemu samochodu przez profesjonalnych techników elektryków.
1. Wyczyść dokładnie powierzchnię instalacji i usuń zanieczyszczenia przy pomocy złączonej chusteczki 3M
2. Przyłóż nakładkę do powierzchni I zaznacz prawidłową pozycję za pomocą markera lub taśmy papierowej
3. Odklej zabezpieczającą taśmę klejącą I połóż nakładkę progową w zaznaczonej pozycji. Klejenie zaczynaj od góry I precyzyjnie przyciśnij na całej powierzchni.
4. Przyciśnij brzegi z taśmą klejącą aby upewnić się, że nakładka trzyma się mocno.
5. Podłącz prawidłowo kable do elektrycznego systemu pojazdu. Podłącz do pozytywnych i negatywnych biegunów zasilania przez regulator napięcia prostownika. Nie podłączaj bezpośrednio do akumulatora!
6. Zdejmij folię ochronną z powierzchni nakładki.
Uwaga
- Taśma samoprzylepna jest bardzo silna !
- Optymalna temperatura instalacji : 10°C - 30°C
- Powierzchnia instalacji musi być czysta, sucha I precyzyjnie odtłuszczona aby zagwarantować trwałość kleju.
- Zwróć uwagę na wodoodporność i wilgoć
- Nie pozostawiaj włączonych nieprzerwanie nakładek dłużej niż 60 minut bez przerwy aby uniknąć uszkodzenia układu LED.
- Producent nie ponosi odpowiedzialności za uszkodzenie spowodowane nieprawidłową instalacją.
Dane techniczne :
4. Napięcie zasilania : DC 12V, czerwony przewód (+), czarny przewód (-) .
5. Prąd roboczy ≤ 600 mA.
6. Temperatura pracy: -20°C ~50°C