42-Mm AIR Sliding Doors

42-Mm AIR Sliding Doors

Product Guide Specification

Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format,including MasterFormat, SectionFormat, and PageFormat,as described in The Project Resource Manual—CSI Manual of Practice, Fifth Edition.

This section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate this section with other specification sections and the Drawings. Delete all “Specifier Notes” after editing this section.

Section numbers are from MasterFormat 2004 Edition.

SECTION 08 13 70

INTERIOR SLIDING ALUMINUM-FRAMED DOORS AND OFFICEFRONTS

Specifier Notes: This section coversAD Systems Officefront Systems interior, 1-3/4”,top hung aluminum-framedand wood framed sliding doors and demountable partitions. ConsultAD Systemsfor assistance in editing this section for the specific application.

PART 1GENERAL

1.1SUMMARY

A.SECTION INCLUDES:

1. Aluminum OfficeFront framing system for interior use.

2. [Interior, 1-3/4”, top hung aluminum-framed and wood framed sliding doors]

3.[Aluminum door frames with sidelight frame components for interior use.]

4.[Aluminum and glass doors for interior use.]

1.2REFERENCE STANDARDS

Specifier Notes: List reference standards mentioned in this section, complete with designations and titles. Delete reference standards not included in this edited section. This article does not require compliance with reference standards, but is merely a listing of those used.

A.ASTM B 221 – Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

1.3SUBMITTALS

Specifier Notes: Edit submittal requirements as required. Delete submittals not required.

A.Comply with Section 01 33 00–Submittal Procedures.

B.Product Data: Submit manufacturer’s product data, including installation instructions

C.Shop Drawings: Submit manufacturer’s shop drawings, including plans, elevations, sections, and details, indicating dimensions, tolerances, materials, components, hardware, finish, options, and accessories. Shop Drawings to show blocking by others.

Specifier Notes: Delete samples if not required.

D.Samples: Submit manufacturer’s samples ofthe following sliding door components:

1.Stiles, minimum 6 inches long.

2.Panels, minimum 6 inches by 6 inches.

E.Manufacturer’s Certification: Submit manufacturer’s certification that materials comply with specified requirements and are suitable for intended application.

F.Warranty Documentation: Submit manufacturer’s standard warranty.

1.4QUALITY ASSURANCE

  1. Manufacturer’s Qualifications: Manufacturer regularly engaged for past 5 years in manufacture of sliding doors and partitions similar to that specified.

1.5DELIVERY, STORAGE, AND HANDLING

A.Delivery and Acceptance Requirements: Deliver materials to site in manufacturer’s original, unopenedcontainers and packaging, with labels clearly identifying product name and manufacturer.

B.Storage and Handling Requirements:

1.Store and handle materials in accordance with manufacturer’s instructions.

2.Keep materials in manufacturer’s original, unopened containers and packaging until installation.

3.Store materials in clean, dry area indoors.

4.Protect materials and finish during storage, handling,and installation to prevent damage.

PART 2PRODUCTS

2.1MANUFACTURER

  1. AD Systems Inc. 2201 100th St. SW Everett, WA 98204 | Website: | Ph: 425-374-1360 | Attn: Estimating:

2.2INTERIOR SLIDING ALUMINUM-FRAMED DOORS AND PARTITIONS

A.Interior Aluminum-Framed Top-HungSliding Doors:

Specifier Notes: Specify model of sliding doors in section C below.

1.Model: AD Systems Office Front System

2.Specified Wall Thickness: [Insert Wall Thickness]

B.Frame Profiles:

1.Extruded aluminum

2.Finish:

Specifier Notes: Specify standard hardcoat (Kynar) finish in Light Sequin or Medium Bronze, other custom hardcoat (Kynar) color option or custom powder coat.Consult AD Systems, Inc.for availability andcolor charts.

  1. Standard: Painted Hardcoat (Kynar) Finish. Meets AAMA 2604.

Standard Colors: [Light Sequin 789G048] or [Medium Bronze 789G046]

  1. Custom Painted Hardcoat (Kyanar) Finish: [Specify Color]
  2. Custom Powder-Coated Finish: [Specify Color]
  3. [ ______].

Specifier Notes: Delete the following paragraph describing panels if frame-kits are specified.

C.Doors:

Specifier Notes: Specify material for doors or reference separate specification section for wood doors, wood stile and rail doors, aluminum doors, etc.

  1. Aluminum Stile and Rail Door
  2. Stile and Rail Size: [Narrow: 2” stiles plus ½” stop, 3 ¼” bottom rail, 2 1/16” top rail], [Medium: 3 ½” stiles plus ½” stop, 6 11/16” bottom rail, 3 5/8” top rail]

[Wide: 5 1/16” stiles plus ½” stop, 6 11/16” bottom rail, 3 5/8” top rail]

10” bottom Rails and muntins available on request

  1. Glazing: [monolithic clear tempered] [safety laminated glass] [sound enhanced laminated glass] [other glass as specified by architect] [optional intermediate muntins]
  2. Door Finish: To Match frame finish or [other as specified]
  1. Wood Stile and Rail Door

Reference Spec Section 08200 Wood Doors or other as applicable. AD Systems requires a minimum 5 ½” rail.

  1. Solid Timber-Strand Core Wood Door

Reference Spec Section 08200 Wood Doors or other section as applicable

  1. Components:
  2. Single Top Track: AD Systems track
  3. Floor Guide: Integral Jamb AD Systems floor guide.
  4. Valances: Extruded aluminum with integral end caps
  5. Top Rollers: tandem nylon roller sized to match door weight
  6. Accessories:

Specifier Notes: Specify required accessories. Delete accessories not required, all accessories listed below are optional.

  1. Soft-Closer: Soft and Self-closing mechanism at [one] or [both] sides of door leaf.
  2. Synchronal Door Drive Coordinator for door pairs.
  3. Handles:
  4. AD Systems Standard Ladder pull: 16” long x 1” diameter. Finish: US32D Satin Stainless Steel
  5. AD Ssytems Standard Straight Pull: 12” long x 1” diameter. Finish: US32D Satin Stainless Steel
  6. Flush Pull and custom pull handle by request.
  7. Door Locks:
  8. Not Required
  9. “ADA Thumb turn Inside only”, FSB Hook bolt lock (Finish US32D)
  10. “ADA Thumbturn inside with occupancy indicator / custodial override outside”, FSB Hook bolt lock (Finish US32D)
  11. “ADA Thumbturn inside with keyed cylinder outside”, FSB Sliding door lock (Finish US32D)
  12. “Keyed cylinder only”, FSB Sliding door lock (Finish US32D)
  13. Magnetic Lock: available upon request. Contact AD Systems for specification details
  14. [Gaskets for improved acoustical performance: acoustic seal by AD Systems.]
  15. [Automatic Door Bottom with integrated floor guide for improved acoustical performance]
  16. [Other] Note: Additional hardware functionality can be accommodated. Please contact AD Systems with your hardware requirements and we will evaluate system compatibility and create specification language.

PART 3EXECUTION

3.1EXAMINATION

  1. Examine wall openings to receive sliding doors for plumb, level, and square.

Note: Finish door operation will be affected by out of tolerance framing.

B.Verify dimensions of wall openings.

C.Examine surfaces to receive top and bottom guide.

D.Notify Architect of conditions that would adversely affect installation or subsequent use of sliding doors.

E.Do not begin installation until unacceptable conditions are corrected.

F. Base of door side to be flush or minimal. Rubber Base acceptable.

3.2INSTALLATION

A.Install sliding doors in accordance with manufacturer’s instructions at locations indicated on the Drawings.

B.Install sliding doors plumb, level, square, and in proper alignment.

C.Install sliding doors to close against walls without gaps.

D.Install sliding doors to open and close smoothly.

E.Anchor sliding doors securely in place to supports. Blocking is required at full width/length of top track.

3.3ADJUSTING

A.Adjust sliding doors for proper operation in accordance with manufacturer’s instructions.

B.Adjust sliding doors to operate smoothly without binding.

C.Repair minor damages to finish in accordance with manufacturer’s instructions and as approved by Architect.

D.Remove and replace damaged components that cannot be successfully repaired as determined by Architect.

3.4CLEANING

A.Clean sliding doors promptly after installation in accordance with manufacturer’s instructions.

B.Do not use harsh cleaning materials or methods that could damage materials or finish.

3.5PROTECTION

A.Protect installed sliding doors from damage during construction.

END OF SECTION

AD Systems Inc.08 13 70 - 1